10 copies of the facility inspection maintenance management system
Equipment facility inspection maintenance management system
Maintenance and repair of equipment is performed by the post where the equipment is located and the post is maintained
The equipment is scheduled, assigned and assigned to the post operator
The equipment arriving at the station is managed, maintained and covered。
1. The proper operation of the equipment to ensure its proper functioning
Unregarded personnel are allowed to spend mechanical equipment at random。
2. Frequent tour of the operation of the equipment and discovery of loose, abnormal sound
Vibration, leaks, etc., should be dealt with immediately and not reported immediately
Processes with shift maintenance workers or reports to the relevant leadership。
3. Discovering special circumstances of equipment which endanger the safety of production or other property
All of this should be done through emergency shutdown measures, followed by reporting to the relevant leadership。
4. Regular cleaning of equipment to ensure that the surface of equipment in use or awaiting use is clean
Obvious corrosion, wear and tear of observation equipment to record and control corruption
Report on the leadership。
5. Maintaining the clean and clean operation of the equipment and ensuring that equipment is not compromised
Some acid gas, waste fluid pollution and corrosion。
6. Refuelling of equipment in accordance with the lubrication requirements
Oil, ensure normal lubricants。
7. Maintenance work on general equipment is conducted on a shift basis, critical equipment
(boiler, rotaryer, gas stove, winder above 30 kw and pump above 30 kw)
Two or more shifts per shift and a small number of times. It is facilitated by the team leader。
8. Recording and handing over maintenance of equipment。
Ashage of equipment pipes due to poor maintenance management
Maintainer evaluated for poor maintenance management resulting in equipment pipe
Damage shall be punishable。
Equipment facility inspection maintenance management system
1. Hammer operators should understand the structure and performance of the hammer and be reasonable
Use, prevent accidents。
Ii. Note the duration of the work of the hammer and perform periodic overhauls, if any, of the spare parts
Damage, which should be replaced in a timely manner so that no more parts may be destroyed。
3. In the course of their work, and in the event of sound noise, stop and repair immediately。
Iv. Regular attention to oil storage in oil cups and to the regularity of lubricants
G/g, e. G. Burning point slag and concentration。
Regular attention is paid to the various components of lubrication。
The distance between the acetate and the hammer, and between the lower acetate and the ground
Should effectively maintain the required distance and check whether the distance has changed
Change to avoid breaking the machine。
7. The integrity of the sphere of the buffer shall be subject to periodic review
It's not like the hammer will break the cover of the work tank。
8. The cups should be packaged during the winter to avoid freezing and hampering the lubrication。
The flexibility of leverage manipulation should be checked before driving。
X. Each refuelling road shall be made accessible through periodic repairs and shall be capable of producing a hammer
To make it work。
11. Electric motors should be kept always clean and removed once a year, but
Be careful not to use kerosene or gas on the online loops when scrubbing in order to avoid insulation。
12. No cold or insufficiently hot metal shall be allowed for exercise。
And the hammer shall not exceed one minute above it, lest it heat
Wasteful capacity, which affects the normal functioning of the machine and the length of its life。
The exercise must have extensive experience in order to manipulate the hammer, especially in the field
In the case of a single strike, there is a greater need for technical skills。
15. The power supply shall be cut at the time of cessation of use。
Equipment facility inspection maintenance management system, section 3
Article i. Implementation and enhancement of equipment operators, maintenance of shipping personnel and
Operation of equipment circuits by equipment managers to ensure proper use of equipment
Management and maintenance, maintenance of equipment, and development of the system。
Article 2 this regime applies to process equipment, pipelines, movements produced by companies
Power equipment, general purpose equipment, crane transport equipment, firefighting equipment, instrumentation instruments
The equipment and other equipment are subject to mobile inspection。
The third is the basis for the careful implementation of a system of mobile inspection of production systems
On top of that, the units, the shipping units must take care of the operators, the machines, the electricity, the equipment, the equipment
`equipment mobile inspection system ' for plant transport personnel and equipment managers to ensure survival
Production equipment is safe, stable and operating over long periods。
The equipment management at level iv must strengthen its personnel, aircraft
Organization of a mobile inspection of equipment for electricity, equipment transport and equipment managers
Leadership. (c) to develop well-established rules for the control of equipment inspections, with clear responsibilities and methods of implementation
Identification of areas, routes, cycles, priority areas and content of equipment inspections yes
Please。
Article v operators, aircraft, electricity, equipment and equipment management people
The officer is going to conduct a careful equipment tour as required by the rules of the equipment inspection
Dismantling the operation of the equipment. During the inspection, the equipment was found to be abnormal and defects were to be eliminated in a timely manner
Recording and timely submission to the relevant department of equipment that cannot immediately eliminate deficiencies
Report。
Article 6 inspectors are required to fill in promptly, accurately, clearly and carefully set
Prepare inspection records。
Article 7 directors of equipment are required to conduct regular inspections of equipment. In
Inspections are conducted to resolve problems arising from equipment inspections in a timely manner. Equipment management unit
It's the law of the state of the prosecution of the professional equipment inspectors
And the use of instruments and the teaching of basic theoretical knowledge for each of them
Steps to improve equipment inspection staff's ability to diagnose and handle equipment malfunctions and ensure equipment
Quality of inspection work。
Article 8 pump equipment is subject to a point check and implementation of the pump management system
Requirements for strict implementation of the large fleet management system for critical fleets
Requirements for special maintenance。
Article 9 units need to constantly learn from experience and improve equipment inspections
Horizontal。
Equipment facility inspection maintenance management system
I. All stationary and mobile equipment must undergo mobile inspection maintenance
System, equipment circuits are primarily carried out by equipment operators, large fixed set
Ready, main transport winch, belts, slippers, various bikes and rollers
Boosters, pick-up machines, etc., are accompanied by maintenance staff who travel at least once a shift。
The content and frequency of equipment circuits must be painted by the competent technicians
To make roving charts. The machine room, the morgue, the workshop equipment tour forms must be made available
Hang it up. Places with no conditions are kept on the patrol
Go back to the record book。
Iii. Equipment operating directors are supply completely completely completely complete the structure
The time, content and requirements are set. No loss, no oversight, no damage
Tiger's off。
Iv. Equipment operational drivers and specialized equipment maintenance workers shall be assigned separate equipment patrols
Back-to-back review of logbooks and timely reporting and processing of problems identified by equipment circuits
In addition, detailed records shall be kept for ease of reference。
V. Aberrants or failure points identified by drivers or maintenance staff during patrols yes
Timely processing and reporting to the dispatch room, and the operation of equipment is strictly prohibited。
Vi. Implementation of the equipment circuit inspection system, sub-districts of machinery and power long
Or the person in charge will check at least once a month and find the problem corrected in a timely manner。
Equipment facility inspection maintenance management system
1. Responsibilities
1. 1 maintenance of hospital-wide medical equipment is performed by the information equipment management department
Responsibility and acceptance。
1. 2 use of critical equipment in the section (including first aid equipment and large valuables) set
There should be personal custodians, operators, who must match them
The device is maintained by a level 1 maintenance, i. E., daily cleaning and dust removal, and the machinery is operated in a time-based manner
Check whether a variety of working conditions are in place before opening? It's confirmed
Use. Operators of other instruments are required to perform level 1 maintenance work on the instruments used
The chief of equipment is required to make frequent inspections, detect problems and report the equipment in a timely manner
Information management department。
1. 3 the director of the equipment information management department has overall responsibility for the organization of the implementation of hospital-wide medical services set
Maintenance and maintenance at all levels. Establishment of practical equipment maintenance, maintenance
The maintenance schedule is regularly maintained。
1. 4 regular (2 meetings/year) medical equipment for the entire compound by the equipment information management department
Preventive maintenance (mainly first aid equipment and essential equipment) conducted on patrol
Problems are identified and solved in a timely manner. Also record the results of the inspection, which is used
The head of the section or the head of the equipment confirm the signature and deliver it to the department of equipment information management
Pipe。
1. 5 during inspection, medical equipment was found to be inoperable or clinical
Medical equipment is in need of maintenance and is reported to the department of information management in a timely manner
Maintenance staff need to organize a force overhaul or request a vendor to repair it as soon as possible
Is it working? Inform the use of the section。
1. 6 large-scale precious equipment and first aid equipment contracted with suppliers to the extent possible
Or maintenance contract, and plant technicians regularly maintain the equipment to ensure
Clinical work proceeded smoothly。
1. 7 responsibility for the use of section operators and section equipment at the end of each year people
The maintenance status is evaluated and the results reported to the functional sections concerned. To the manufacturer
Maintenance of technical staff is also evaluated。
Workflow
2. 1 use of critical equipment (including first aid equipment and large valuables) in the section set
(b) the equipment and conventional equipment shall be kept, operated and maintained at level one
That's cleaning and dusting every day. The machine should be lubricated and checked for all kinds before it goes on
Are conditions in place? It is open after certification。
2. 2 regular (2 meetings/year) medical equipment of the equipment information management department for the entire compound
Preventive maintenance (mainly large precious equipment and first aid equipment) on patrol
Problems are identified and resolved in a timely manner. We'll also record the results of the inspection
Results are recorded。
2. 3 large and valuable equipment, first aid equipment and critical equipment, as far as possible
Contract for warranty or maintenance, fixed term (1 to 2 times per year)
Maintenance of equipment。
2. 4 responsibility at the end of each year for the use of section operators and section equipment people
The maintenance status is evaluated and the results reported to the functional sections concerned。
Equipment facility maintenance management system, section 6
Purpose
To ensure the proper and efficient functioning of the equipment, reduced downtime and enhanced set-up
Provide for security in operation。
Scope
The system is suitable for equipment operators within the company。
3. Maintenance of equipment
The equipment operator should have mastery of the "threes" and "fours" of the equipment
"three good" and "four good" mean: "manipulated, used, repaired, used
Maintenance, inspection, general failure. "lubrication 5" means
Set, fixed, fixed, fixed, quantitative, fixed。
Once the equipment is operational, the equipment should be maintained so that it is not inside the machine bed
Processing of scrap, workstations clean, flexible, appearance, cleaning, equipment in place
Initial state and completion of equipment maintenance log。
The current operating processing process should be completed before the equipment is shut down and the equipment should be shipped to each other
Move parts back to their original location, then press the stop button and then turn off the power
Directly pull the gate。
Maintenance of equipment should be performed after the stoppage and water and cooling fluids are strictly prohibited
Cleaning or cleaning directly electrical components, cabinets, much less using compressed air
Blow electrical components or cabinets。
When the equipment is working normally, an electric or button box or a branch box is not allowed open
(unless necessary for equipment to disperse)。
In the process of processing equipment, operators are prohibited from leaving their posts without permission. Due to inspection
Work has to be done, etc., to leave, the machine bed has to be stopped and the equipment has to be suspended
Run。
When equipment is maintained, the operator should actively cooperate, and after the maintenance is completed, the operator
Air transport must be conducted immediately and check the correct installation of the various parts of the equipment and then
The first inspection shall not be carried out directly for any reason whatsoever by delaying or not conducting air transport
Production, completion of maintenance of equipment completed by maintenance personnel
Confirmation of the signature of the operator and the head of the department。
The operator is not allowed to alter the machine-bed parameters, process the process, and set the password
During the automated processing of equipment, the operator is prohibited from adjusting the main axle factor or entry without permission
Give it a multiple, it is forbidden to press the double button. In the event of an accident (e. G. A broken knife)
The button should normally be pressed first and not directly to the stop button。
When the equipment fails significantly, the operator cannot take care of himself
I. E., reflect to maintenance staff and provide as much accurate malfunction information as possible, such as which equipment
What action was not performed, failure alarm content, failure description, etc., and protection
Site to rationalize maintenance staff and cause of failure analysis。
3. 10 at the moment, each plant is operated by more than one person
The operator on duty is designated as the first person responsible for the equipment and must be in the facility
Sign the maintenance log form, and the equipment department will book the aircraft according to the order handed over from the workshop
List checks. The first responsible person is strictly forbidden to hand over the equipment to another person without permission。
3. 11 operators shall not place personal effects on equipment and electricity shall be prohibited
The cabinet serves as a storeroom, with a variety of miscellaneous items such as rags, tools, gloves, etc。
3.
