A complete maintenance code for toshiba photocopiers
Press 0 and 1 at the same time to open all the power panel lights and release them by clearance/stop
Both press 0 and 2 to open the power machine into the old mode, show ag, and press 09 to disarm
At the same time, press 03 or 04 to open the power machine into the input/output inspection, display ch, enter different
The code can activate different components, such as the 03-33 flash light check
Press zero and six at the same time
Press 0 and 7 at the same time
Press 03/04 to open the power simultaneously, enter an input/output check to show ch, exit and press 09
1 main generator, on11offf
2 paper-to-paper compressor on12ff
3-positioning plaster clutch on13offf
6-moderator o16offf
Seven cooling fan on17ff
Total 10s press p
20 scanners move 50% and 200%
Twenty-one camera press p, 50% moving at 200%
Twenty-two mirrors move 50% and 200%
Thirty-one reprint output press p. N. And then p. O. Ff
32-separated output press p. O. P. And press p. F
33 luminous light output, press p
34 pre-print offset press p. N. And p. F
40 on a cardbox, press p. N., press p. F
41 on the card box for paper hyper press p. N. And p. F
Forty-three on cardbox electrics, press p. N. And then p. F
Forty-four paper boxes for paper clutches, press p. K. And press p. K. F
These are the detection codes, which are usually used only for 03/040508, which are used by the old machine by air。
1. Replacement carrier
And press 05, turn on the power switch, panel aj, enter adjustment mode n, and press photocopier nose
? Automatically) adjusts, types the modified value, press the insert key to deposit the modified value in the memory, press 3+4 copying --
0td sensors automatically adjust --
Type 0, about two minutes panel display started automatically changing the short time to show when working with a copying drum and a projector
Organisation i don't..
Display value = 24 (2. 4 ± 0. 5v), insert key into memory and exit by 09
Exit from diagnostic 05 mode: type 09
Clear maintenance number
Press 08, turn on the power switch, panel ad, type adjustment mode n, current
Value, make (automated) adjustments, type the change value, press the insert key to deposit the value in the memory, press 3+4 to copy
69 --pm (maintenance cycle) interval -- range: 0~999,999 default value = 0
79 - current pm count shows range: 0~999,999 default value = 0
The maintenance number appears when the value shown by 79 reaches the value set by 69, and the maintenance period is reset to eliminate
Maintenance number
Exit from diagnostic 08 settings mode: type 09
Additional information on this item
Partially adjusted code for the x+5 copier
1 manual exposure adjustment 100% range 0-255 standard 128
2 manual exposure adjustment of 154% range 0-255 standard 128
3 manual exposure adjustment 50% to 255 standard 128
4 manual exposure adjustment 200% range 0-255 standard 128
5 automatic exposure adjustment 100% range 0-255 standard 128
Automatic exposure adjustment of 154% range 0-255 standard 128
Auto-exposure adjustment 50% range 0-255 standard 128
8. Automatic exposure adjustment 200% range 0-255 standard 128
14 image exposure adjustment 100% range 0-255 standard 128
15% image exposure adjustment range 0-255 standard 128
16 image exposure adjusted 50% to 0-255 standard 128
17 image exposure adjustment 200% range 0-255 standard 128
38-string partial output range 0-25-5 standard 128
39 reprint voltage adjustment range 0-255 standard 128
40-separated weight adjustment range 0-255 standard 128
42-barrel pressure adjustment range 0-25-5 standard 128
*49 automatic exposure adjustment
*0 auto ink adjustment set to 24
*90 automatic ink powder adjustment range 0-255 standard 128 (means adjustments for automatic ink powder sensor)
0+8 on
*69pm counter setting mode 0-999,999 initial value 00: invalid pm counter request
79 current pm counter value 0-999,999
Tung chi copier exposure adjustment code
Press zero, five
1 - manual 100% exposure adjustment range: 0-255, default value = 128
2 - manual 154% exposure adjustment range: 0-255, default value = 128
3 - manual 50% exposure adjustment range: 0-255, default value = 128
4 - manual 200% exposure adjustment range: 0-255, default value = 128
5 - automatic 100% exposure adjustment range: 0-255, default value = 128
6 - automatic 154% exposure adjustment range: 0-255, default value = 128
7 - automatic 50% exposure adjustment range: 0-255, default value = 128
8 - automatic 200% exposure adjustment range: 0-255, default value = 128
9 - exposure cap adjustment range: 0-255, default value = 255
10 - lower exposure limit adjustment range: 0-255, default value = 0
14 - photo 100% exposure adjustment range: 0-255, default value = 128
15 - photo 154% exposure adjustment - range: 0-255, default value = 128
16 - 50% exposure adjustment for photographs - range: 0-255, default value = 128
17 - photo 200% exposure range: 0-255, default value = 128c1 - main power lock stay
C21 -- optical system failed to complete initial. Optical system locked
C26 -- exposure lights burned
C32 - unbox (ua) td sensor automatically adjusted failed
C41-- when the power is connected, the accelerator is abnormal or the light is open
C43-- during preheating, or after preheat completion, the determined heat sensitivity electrical abnormality
C44 -- during preheating, or when the preheat is finished, the lights turn on
C54 - page breaker - and main cpu error
C55 -- adf- and main cpu error
C71-adf main generator locked
C72 - bad adjustments detected by positioning sensors
C73 - eeprom initial bad
C81 -- page breaker paper transponder anomalous
C82 - page breaking transverse
C83 -- page breaker maximum error
C84 -- page break error
C85 - page breaker location sensor error
C86 - page break sensor error
C94 - the optical system failed to complete the initials at ch (aj) mode. The optical system was locked
E1 - indoor card paper
E2 -- card card near the shot
E3 - paper kept in photocopiers while power was running. Internal
E4 - front door opening during photocopying
E5 -- cardboard near the tablet
E14 - bottom box feed paper
E71 -- adf draft piece card
E72 - adf transfer partial card
E73-adf script part card
E75 -- adf2 plus 1 (second in draft transmission) card
E81 - part of the copy of the paper from the page breaker arrived longer than the card paper, and the paper did not reach the sensor device
E82 - paper breaker partial copy paper waiting longer than card paper, paper parked on sensor
1568 error list
"cleaning cardboard" or "request for overhaul" symbol clicks: "clear/stop" and
The 8 key displays the following error codes:
Photocopier cardboard
Error code content allowance
Card paper in the e01 copier, including handycard paper (led by side)
Paper in the vicinity of e02
E03, when the power is turned on, card card
E05 failed to reach the gps switchboard paper after pfu was used to transmit the paper through the transfer pad
After ppc's paper
2. Carcards in paper supply
Error code content allowance
E14 down cardboard (pfu) paper does not reach the transfer pad
3. Card paper in the adf transmission path
Error code content allowance
E71 in the adf text for cardboard
