Preparatory work for the examination
(i) the period of validity of the examination on the licence sub-certificate, which may be attended within three months, including this month, prior to the expiration of the examination。
(ii) to check whether the vehicles under inspection have unprocessed traffic violations and accident records, through the tma extranet, hand over 12123 app, where there are unprocessed records of traffic violations and accidents, where there are unprocessed records, to be processed in advance at the transport unit (large) law enforcement stations and to pay a fine to the business bank。
(iii) vehicles should be inspected and maintained at 4s stores or repair workshops, the vehicle should be cleaned, there should be no visible oil spills, water leaks, gas leaks, tyres are intact, tyres have normal air pressure and there is nothing alien in the beads, the engine should operate smoothly, without delay or sound; vehicles equipped with a vehicle-mounted diagnostic system (obd) should not have fault information related to the abs, the eps and other safety-related failures。
(iv) examination of vehicle tyres, non-conforming with axle tires, abnormal wear and tear of tyres, punctures on the face and on the wall sufficient to expose the curtain layer, non-conformity in the draught depth, and timely replacement of tyres of the same size。
(v) check the window glass of the vehicle, all of which should be intact and without a mirror reflecting mask。
(vi) check lamps, instrumentation instruments, all types of lamps and instrumentation shall be fully functional。
(vii) be equipped with effective fire extinguishers (except for small, mini passenger vehicles) and triangulation warning signs for motor vehicles。
(viii) in the case of an unlawful retrofitting, restitution。
(ix) dismantled and reversible plates to be removed。
(x) check the body of the vehicle, with paint broken and the timely repair of car rust; no vehicle, other than a bus, is allowed to spray body advertisements or to influence colour signs, patterns, text。
(xi) check vehicle plates. Cards are not clear and complete and should be replaced if they affect identification. The installation requirements for the metal material plate are as follows:
1. Should be face-to-face and the characters should be placed on board the plate (mount) and it is prohibited to reverse or reverse。
2. The front plate shall be installed in the middle or right of the front end of the motor vehicle (in the direction in which the motor vehicle moves) and the rear plate shall be installed in the middle or left of the back end of the motor vehicle, without prejudice to the safe conduct of the motor vehicle and the identification of the licence plate。
3. Installation to ensure that the plate is free of any deformation and cover, horizontal level, and vertical fundamentals direct to the ground, with vertical angles not greater than 15° (the motorbike plate is tilted upwards by vertical angles not greater than 30°)。
Installation holes shall be fitted with secure seals that meet the requirements of ga804, except to the extent that they cannot be installed under vehicle conditions。
5. When installed using a placard-aided installation, the edge of the outer edge of the plaque is greater than 5 mm from the edge of the registration number of the motor vehicle, and the production sequence identification shall not be covered。
No other light source for impact card recognition shall be found around the board 6。
(xii) reflex marking of the truck, rear and rear protective devices meet the requirements。
(xiii) the carrying of a driving permit at the time of the examination, the payment of insurance certificates for compulsory insurance coverage for motor vehicle traffic accidents in the provinces and municipalities abroad, as well as the payment of taxes or tax exemptions on motor vessels。
(xiv) cars can be examined via the tma extranet, telephone, micromail appointments and hand over 12123 app。
Cases of non-adoption
(i) the registration of the motor vehicle does not correspond to the circumstances relating to the motor vehicle。
(ii) oil and water spills in engines。
(iii) if the vehicle number plate is forged, altered, defaced, unwritten and does not contain the required sealing device。
(iv) catalyst failure lights were activated and related malfunctions were observed。
(v) unlawful modifications, encircling, tailings, towings, towing hooks, pedals, etc., personal improvement of exhausts, self-retardation of seats, lamps, skylights, etc., and changes in the specifications of tyres, container boards, steel springs, etc。
(vi) inconsistent with axle tyres or abnormal wear of tyres and severe wear of tires。
(vii) the windows of the vehicle are broken (fissified) and the mirror reflector is posted。
(viii) personally changing the colour of the car, except for the car that is advertised。
(ix) the van did not carry the required reflector markings and the protective gear was inadequate。
(x) other non-compliant requirements of national motor vehicle safety technical standards。
