... Sy-50yc8201q pressure cooker cooking problems in soupor are usually caused by the failure of temperature control, bad seals, abnormal or improper use of heating systems. I have given the following systematic maintenance options in conjunction with the common malfunctions of the supor pressure cooker, which can be sequenced:
Temperature control and sensor system overhaul (core failure zone)
1. **checking magnets for thermostats**
... This is the most likely to cause burning and is located at the heating centre. If there is dirt on the surface, oil stains or an ageing internal spring, this may result in the failure to break temperature protection in time for cooking and the continuous heating of charred rice:
... To remove the oxidation layer by removing the cap, lightly rubbing the thermostat contact point with sandpaper
... Test magnetism of magnets: a screwdriver should be able to suck at constant temperature and eject automatically up to 103 °c ± 2 °c. If it does not work, the same type of magnet will have to be replaced (sy-50yc8201q usually matches 2500w specification)
2. ** detection of thermostat components and pressure switches**
The component controls the internal pressure and temperature of the pot:
... The temperature is miscalculated in the event of electrical resistance abnormalities (e. G. Fractional voltage resistance r126 damage). Measurement of con203 plug voltage with a mass gauge. 10 k of subvoltage resistance is required for deviation from 2. 5 v
... - pressure switches are too high for control (>70kpa) to cause extreme temperatures. The counter-clockwise micro-tip switch lowers the pressure ceiling and boils the water: the pressure limit valve should be vented intermittently instead of continuous jets during the pressure phase
Pressure and seal system overhaul (key leak-proof points)
1. **replace ageing seals and support rings**
... The leak causes a shortage of pressure and the electric boiler continues to heat up the temperature:
... To check if seals (silica ducts) are fractured and hardened, especially if the precipitating edges require replacement of the original plant
- ... The support circle (sealed fixed circle) of the pc material is hydrolysed and broken, causing a leak in the pot mouth. Need to break the cover to replace the yd1/yc1 series dedicated support ring
2. **limited pressure valves and buoyant valves overhaul**
... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- test float valves: the heating of the lids should be tightened up and, if the truck is stuck, the pusher should be cleaned or pressure spring replaced
Iii. Heating systems and internal boldness screening
1. **thermal pallet and internal choreography tests**
- ... A local bulge of the heater can lead to an imbalance in heat. A straight-foot measurement of the disc plane level, deviation > 1 mm to replace
- courage grafts or deformations (especially after washing with a steel ball) affect the heat. Press the bottom of the heart, and if you feel like it, you need to change it
2. ** cleaning and exposure optimization**
- ... The removal of carbonated grains of rice from the heater and the base of the inner gall (alcoholic rubbing)
- ... To ensure that the inner urchin is fully aligned with the heater and rotates several times around it
User habits and maintenance adjustments
1.** water volume and operational amendments**
- ... Pressure pots should have less water than normal meals (m: water: 1:1. 2) and ensure that the grain is evenly paved
- ... Cooking completes the natural depressure in 10 minutes before opening the cover, so as not to force the exhaust to cause the bottom to evaporate too fast
2.** periodic depth maintenance**
- ... Boiled once a month with a mixture of vinegar plus water (1:2) and dissolved with water
- half-yearly change of seals to avoid oily silica
... Significant safety alerts: it is recommended to be sold after delivery if it involves dismantling to detect circuit boards (e. G. Cpu short-circuits) or replacement of heating pallets. Forced maintenance may trigger e0/e1 failure code (available for reference)
Supor official fault code form. Maintenance flowchart
Burning rice
}b {check thermostat actions}
B-o-o-o-o-o-o
Cleaning or replacing magnets
"b-"- "b" is normal
D--and--and--and--and--and--and-and-and-and-and-and-and-and-and-and-and--and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and-and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and and
Replacement of seal/support ring
D-- | normal pressure
F--l--l--l--l--i--i--i--i--i..
Change deformed heater
F-- | | | | | | | |
Adjust the ratio of water to 1:1. 2
... On the basis of the above process, over 80% of the burning problems can be located. If it is still not possible to exclude, it is necessary to focus on the problem of the temperature control on the computer board (to connect the debugger to the sy-50yc8201q specific solid). Maintenance records are maintained, and subor can request a replacement for repeat malfunctions。
