The label is part of the product label and is an essential indicator of the eligible product. Labeling requires the use of label printers, which are dedicated to a large number of printing devices that can quickly print non-dry glue labels, pet labels, caps, water washes, etc. There is a very wide range of applications, for example, in supermarkets, label information on clothing, logistics, etc., and among the many label printers, brother label printers are quite a good one. How do we repair them if they have problems? Today we're going to see what's going on with the maintenance of the brother label printer and what's going on?
Problems and maintenance methods
Question 1: why can't we cut the ribbons after the labeler has implemented automatic paper cutting?
Reason: after a long period of use, the back tape is attached to the cutter, which leads to a normal cut of the tag. Or maybe the cutter got numb。
Solutions: turn off the label power, open the hood, remove the ribbon. With cotton, a little alcohol, a light swirling of the cutter's edges. If this is not possible, replace the cutter. (replace the cutter and contact the dealer)
Question 2: how do brothers label printers get back out of the plant?
Solutions: each type of label printer has a different setup, but it can be restored to the facility as long as it is fully deleted. For more details, please refer to the instructions for the use of the brother labeler
No hint on the label screen after 3?
Reason: batteries are not installed correctly, battery power is inadequate and power adapters are not working properly。
Solutions: check batteries, power adapters。
4. Why do stripes appear when label machines are printed?
Reason: the ribbon is exhausted。
Solutions: new ribbons are installed and then press the " paper feeder/cutting button " or turn off the device and restart the label printer。
Five, why is the power button for the label printer, the signal light not flashing or not?
Reason: the main reason is that power connections are not closely connected。
Solutions: check whether the power connections are correctly connected. If the label is still not functioning properly, contact the point of sale where you purchase the label or the local authorized service provider。
Why can't my brother's labeler take a good belt?
Reason: the tape cannot be removed if the label printer's scrolling axis is working and the power is suddenly out。
Solution: opens the label printer power and removes the tape when the scroll axis returns to its initial position. (the user is strongly advised to use the power button to close the label. I'm not sure
7. Why does the tag opportunity sound as if it were printing after the printing mission?
Reason: this is because the autocutor maintains the cut status of the next label after the printing task. If no printing task is performed within 10 minutes, the automatic cutter will return to its initial position and sound. This is the normal operation of label printers。
8. Why is it not clear that the labels printed by the labeler have black or white lines or printed content?
Reason: if the label printer is used for long periods of time, the printer will be dirty of the inside header and the print rolling axis. You can use the following two methods to clean headers and print scrolls。
Solutions:
(1) automatic clean-up: special cleaning belts using label printers. Opens the printer, loads it with a clean ribbon, press the paper feed/cutting button, and press 2-3 again depending on the number of times the printer is used. (recommended to use clean ribbons)
(2) manual clean-up: open the printer and use clean cotton sticks to gently wipe the head of the print and print the scrolls. The printing head just finished is hot. Please clean it later
Pt-2420pc labeler available on one computer, why can't it be printed instead of another?
Reason: this is because pt-2420pc is protected by a serial number and can only work on a computer with its serial number。
Solutions: if you want to use another computer, you must re-install the driver on the computer. If pt-2420pc has been installed on the same computer, the print port must be reset。
10, tag printer installed, power turned on, why can't it be printed?
Reason: there are several possibilities: (1) the connection is not correct. (2) the correct label printer was not set. (3) no print port has been selected. (4) the hood was not closed. (5) the tape is not installed correctly。
Solutions: make sure that the usb line is connected to the computer and the p-touch computer tag printer, and if it is still unprintable, select the port setting in the printer attribute and select the correct p-touch computer tag printer port。
11. When the installation process is complete, why is there no p-touch computer label printer on the computer?
Reason: before installation, please be careful not to connect the p-touch label printer to the computer, which will not detect the machine if the p-touch tag printer has been handed over to the computer before installation of the driver。
Solutions: remove the installed driver and re-install it. During the installation, the p-touch computer tag printer is connected to the computer only when the system hints。
12. When printing with a portable labeler, the colour belt is not available. Why?
Reason: there are several possibilities: (1) the ribbon is run out. (2) no printout was entered. (3) printed content is not confirmed. (4) tape. (5) no electricity。
Solutions: check colour belts, power sources, confirm what needs to be printed, check and clean the cutter。
This is the description of the maintenance methods and failures of the brother label printer, which you have listed, and which, if it does not solve your problem, can be tested at the corresponding maintenance point. Label printers are printed very quickly, which facilitates our lives, but during their use, additional maintenance is required to maximize the useful life of brother label printers。
