1. The method of breeding wind-level trees
The way peace trees grow
The tree of peace, also known as the tree of a thousand years, because of its sacrificial form and its meanings are blessed and well-pleased. Below is a description of how the tree was cultivated:
Soil selection
Psychic acidic to neutral defusing soils. It is possible to mix leaves, gardens and sand at a ratio of 3:5:2 and to add appropriate weight-based fattening to produce a cultured soil。
2. Light conditions
And the peace tree is bright and patient. In the growing season, sufficient light should be provided to avoid direct sunlight. During the winter, it can be maintained in the light of indoor light。
3. Watering
The tree of peace is more drought-resistant, and not enough water should be poured. During the growing season, the soil is wet, but no water is accumulated. Water should be brought under control during the winter, and soil should be dried up。
Fertilization
The tree of peace is growing during the season, and every half-month it is able to produce thin fluid. Stop fertilization in winter。
5. Cutting
The peace tree is growing rapidly and needs to be trimmed in time to preserve the beauty of the stock. It can cut off long branches, dead branches and weak branches and can be shaped according to the preferences of the individual。
Can the peace tree plug work
Safe trees can reproduce through plugs, with higher survival rates. This is done by:
1. Selection of plugs
Select a strong mother strain, cutting the top ten to fifteen centimetre long branch as a plug。
2. Processing plugs
Cuts the angle at the lower end of the plug to 45 degrees, removes the next leaf and retains only 2-3 leaves on the top。
3. Rooting
Root powder or willow water may be used to impregnate the bottom of the bar for 10-15 minutes to promote root。
4. Plugin
Ready for loosely prepared breeding soil with plugs inserted into the soil at a depth of 3-5 cm. Press the soil lightly and keep it moist。
5. Conservation
Plumbing is followed by the maintenance of soil moisture and its placement in warmth and light. Usually, two to three weeks can take root。
2. The method of breeding wind-level trees
The culture of wind-level trees
Soil
The soil of the peace tree, which is soothing and irradiated, may be mixed with garden, leafy and sand at a ratio of 2:1。
2. Light
The tree of peace is radiant, but shade-resistant, and may be placed in a place full of scattered light. And the summer shall be covered with shade, lest the leaves burn。
3. Watering
The tree of peace is humid, but water is withheld. The growing season can be watered once for two to three days, and the frequency of watering can be reduced in winter。
Fertilization
Safe trees require low levels of fertilizer and can be applied with thin organic or compound fats every 1-2 months。
5. Cutting
The sauna strain is of a high type and can be controlled by shearing. Every spring or autumn, long and dead branches may be removed and the branches trimmed。
Can the peace tree plug work
Injection selection
A healthy, insect-free safe tree sheath is chosen, and half-wooded branches are cut for insects。
7. Injection
Removes the leaves from the lower part of the slot and retains only the top two to three leaves. The length of the plug is 10-15 cm。
8. Plugin matrix
The platinum matrix may be used for neptunite, pearl rock or river sand. The matrix needs to be wet, but not water。
9. Interpolation steps
Plugs are inserted into the matrix at about half the length of the piping. Put pressure on the matrix, and avoid poking。
10. Post-plugged management
Keep the platinum moist and provide sufficient dispersive light. Covers the direct light and avoids the water loss from the ear。
11. Root time
It takes weeks to months for the trees to take root for longer. Roots can be gradually transferred to the soil。
3. How to reproduce the tree, how to map the tree
The method of breeding the tree
The tree of peace, also known as the zakat, is beloved by its blessed and beautiful meaning. It is easy to acquire new green plants for themselves or for friends and relatives, and to add life and blessings to the way they reproduce。
I. Putting
Plugging is the most common method of breeding safe trees, operating with simplicity and a high rate of survival。
1. Preparatory materials
A healthy safe tree mother
Sharp scissors or blades
Aqueous plating matrix (e. G., neptunite, pearl rock, peat soil)
Root powder (optional)
2. Selection of slots
Strong, disease-free branches are selected from the mother farm for approximately 10-15 cm length。
Keeps 2-3 pairs of leaves while cutting and removes the lower one。
3. Treatment of slots
Angular tilt of the piping to an angle of 45° to increase the area of exposure to the matrix。
The stem base can be immersed in a root powder solution for several hours to promote rooting。
4. Plugin
The handled plugs are inserted into the ready piping matrix at a depth of approximately 5-7 cm。
Lightly pressurized matrix, which closely connects the incision to the matrix。
Management
Put the piping basins where there is dispersing light and warmth。
Keep the matrix wet, but no water。
Spray water fog every 2-3 days to increase air moisture。
Ii. Solution
Seeding can also be used to breed safe trees, but at a lower rate of survival, it takes longer to germinate。
Preparation of seeds
Seeds are extracted from ripe trees of peace。
Seeds are immersed in hot water for several hours to promote growth。
Seeding
The seeds are spread evenly into the ready seed base, covering a thin layer of soil。
Keep the base humid and provide a warm and bright environment。
Management
The emergence of seeds requires a gradual increase in light intensity。
Fertilizing and promoting growth of seedlings when appropriate。
With control of the tree's breeding methods, it is easy to add a blessing and a green meaning to the home. Whether you choose interpolation or sowing, they thrive and bring peace and good luck to your life。
