Does it always feel like the screen's rubbing up? The monitors, the notebooks, they're six months old
Don't start with the poor quality of the screen! It's probably the way you clean the screen。
Many people smoke paper towels and rubbing alcohol with their hands, even though these are routine operations, and are quietly destroying your screen: light corrosive dizziness-proof coatings that allow the screen to mist forever; heavy fluids penetrate into the fuselage, directly causing short roads to fail。
Today, you've been able to sort out the officially approved screen clean-up plan, the red line to avoid the pits, the correct step, and the new guy can do it wrong, and you're not afraid to break the screen anymore。
Avoid the pit! 90% of the people got four fatal mistakes
These operations are looking at "clean and cheap," and they're hurting the screen every time
Mistake 1: alcohol / disinfection directly, disinfection one step in place
Whether lcd or old screen, there's a special nano-painted layer on the surface that's dazzling and fingerprinting. Alcohol, ammonia/propanone / bleach cleaners directly dissolve, corrosive the coating, which may not be seen from time to time, and permanent use of the screen causes irreversible fog, varnish, and can no longer be repaired。
Mistake 2: grab a towel, wash a towel, wipe a screen
Paper towels and towels look soft, but there are plenty of wooden fibres and hard particles invisible to the naked eye. Dry-wielding is like grinding a screen with sandpaper, leaving indelible tiny scratches, grafting through the flowers, causing greater harm to the precious old screen。
Error 3: spray the liquid directly on the screen
This is the most dangerous operation. The liquid penetrates into the airframe following a gap in the frame of the screen, lightly causing water marks on the screen, backlight marks and direct short-circuit burning of the main plate, with notebooks and one-stop machines being particularly easy to hit, and many people simply get the equipment out of service。
Zone 4: scrambling around like a table
Back and forth rubs allow dust particles to be stuck between the cloth and the screen, scratching over and over and over, while a strong pressure can also damage the pixels point of the oled screen, causing damage, burning the screen and completely destroying it。
We'll do it before we clean it up
Step one: shut down the equipment and completely disconnect the power
Not only to avoid short-circuit risk, dust, fingerprints, stains on the screen are better visible, cleaner, and do not leave a dead end。
Step 2: holding the equipment correctly
When cleaning laptops, portable monitors, you must hold the frame of the machine, not pull the bottom, wire, let alone squeeze the corner of the screen, so as to avoid a slide of the fuselage and a fracture of the screen。
Officially accepted correct clean-up steps, zero failure to break step 1: dry dust removal (most critical step, never to be saved)
Take a clean, fine fibre cloth (special screen cloth, clean glasses, no hair, no hard particles) and wipe the screen in the same direction and wipe all the dust and hair from the surface。
Focus: it must be dry first! If the dust is not cleaned first, the dust particles will be rubbed repeatedly between the cloth and the screen, and the screen coated directly。
Step 2: wet cleaning, treating only persistent stains
If after drying, there's still prints, oil stains, then do it again
Placing pure water in a spray bottle, spraying only one or two times on superfiber sheet, spraying the cloth into a micro-moisture state, without a single drop of water, and in no way permeable。
Then, in the same direction, rub the stained area softly, do not rub it back and do not press the screen。
Red wire reminds us that water must not be sprayed directly on the screen! It can only be sprayed on the cloth! It is pure water only for the entire journey, and no detergent or detergent。
Step 3: dry end to avoid water stains
With a dry and clean area of cloth, and in the same direction, slowly dry up the tides on the screen, focusing on cleaning up the tides at the edges of the screen and ensuring that there are no water stains。
Oled screen exclusive alert! 3 red lines must never be touched
Many of the laptops and monitors are now oled screens, more expensive than the lcd screens. Except for the above rules, this is absolutely impossible:
No alcohol, no organic solvents, even if diluted, can be used to directly destroy pixel seals and screen coatings; no pressure screens should be pressed hard, the pixel dots of oled are soft structures, which can cause direct damage and permanent burn screens; just-out heat screens should not be cleaned immediately, the machine cools for 10 minutes, cleans up at high temperatures, the coatings are more easily damaged, and thermal inflating will make it easier for liquids to penetrate the air bodies. Don't step on the hole after cleaning
Just put it in the ventilator and dry it. Don't blow it with a blowtorch! A hot wind can damage screen coatings and fuselage components, and a cold wind can bring dust and fur back to the screen
If the wind is dry and there are water marks, it can be smoothed in the same direction with clean dry superfiber。
Focus! Remember, four core principles, never step on a pit
Power cuts, then operations, and safety always take precedence; dry, wet, pure water is enough; only thin fibre cloths in one direction are wiped softly, with no pressure; no direct spray screens, no alcohol, organic solvents etc。
The screen really isn't so delicate, and it doesn't have to be cleaned often。
