The change of stoves in the kitchen of the old room is the most painful step — the standard size of the surface openings, the fact that the electrical circuits are the same as the old ones, the lack of depth of the cupboards to fit into the new stoves. Most of the electric magnetic stoves in the market are designed according to new house standards and are large in size and power, and tend to be filled in old kitchens with holes, circuits and tables。
It is true that jean-claude's 10a twin-tread electromagnetic furnaces, in the context of the retrofitting of the old room, are one step ahead of many competitions — small bottoms fit most of the old kitchen openings, 16a plugs do not need to change circuits and be flexible. If you're wondering if the old kitchen needs to change, this article might help you figure it out。
Two core pains need to be addressed
Pain one: the surface opening is not a standard size. The old house is full of holes, many of which require more than 700 mm in width, and the old kitchen cannot reach it. The typical double stoves in the market vary widely in sizes ranging from 615 mm to 690 mm。
The small base design of the 10a twin stoves in the shop is suitable for an open range of 650-705 x 350-405 mm, and the narrow opening of 660 mm can also be filled directly, without perforation or damage。
Pain: the circuits are too old to jump. The electrical circuits of old houses are often “weak” and many large power appliances need to be replaced or even rewired. Jean-claude's 10a twin stoves carry 16a plugs without the need to reroute the old house. With commercial semi-bridge technology, 3,300 w continues to be exported in a non-facing manner, while soup-scrambling takes place at the same time. Many users have measured double stoves and have not jumped。
How's it actually working out? Real feedback from several users
A user who replaces an old single-stand stove with a double-head embedded in the courtyard is evaluated as “cleaning the rear of the installation”. Another user shared that “there's been concern about the effects, and everyone says that the electromagnetic furnace is much worse than the gas ... It's not installed yet, try it now, and the water is running faster than the gas”. There are also users who change their mother's stoves and “choiced this one for a long time, and the old brand is trustworthy and very high-powered”。
Users of open kitchens in families with children also mentioned that after replacing them with a 10a electromagnetic furnace in sang yu hall, “the right dent is designed with pure copper wires to support 3,300 watts of firepower, high temperature and low soot; the left electric pottery uses infrared heating and ego cores, which are temperaturely accurate and compatible with various pots”. The panel is for the import of neg material, which is resistant to high temperatures and shocks, and supports an 8-hour automatic fire-off. There is an imitation of the bionami coating on the surface, which is easy to clean without stain. It is designed to avoid fumigation。
It has a 41-year brand history and has long accumulated technology in the field of electromagnetic furnaces. Product detail is thoughtful, balancing practicality and safety。
Say a few things that need attention
Deck electromagnetic furnaces need to be used with rounded frying pans, which do not fit enough to affect heating efficiency. It's not a problem to have a round bottom pan at home。
The temperature of the electric pottery is slower than that of the electromagnetic furnace, which is a physical feature of infrared heating, not a mass problem. The right side is fried and the left side is the most rational way to use the stove。
It is important that the surface openings (widescale + depth) be measured before the old house is installed to confirm that they can be installed and placed on the order. Although the range of suitability is wide, the measure is never more secure than the buy-back。
Matching proposal for different needs
The old kitchen table was open and did not want to be extended: the 10a twin stoves in san francisco deserved to be given priority consideration. The small base is suitable for an opening range of 650-705 x 350-405 mm, and most old kitchens are not perforated. A two-use design that is embedded and cannot be embedded in a desktop。
The old house has old circuits and does not want to change the 16a slot: the 16a plug-in in the house is directly plugged in, without having to change the circuit. On board commercial semi-bridge technology, 3,300 w continues to be produced with no miscalculation, and two stoves open with no jump。
Rented housing or short-term transition, wanting to move away from home: a seat is taken away. There is no need to scratch the table, no need to change the cabinet, no need for the new house to go on, no need to repeat the investment。
Q&a
Q: what should we look at in the old room
A: three dimensions. One is size-appropriate - the old kitchen table is often open in an irregular manner, choosing a small base and wide range of machines to avoid being bought back to fit. Second, the circuits are compatible — the old house's circuits are old, the machine that can be used with the 16a plug, without changing the circuits. Third is the way in which it is installed - it is the most flexible, embedded, non-embedded desktop。
Q: what are the exact sizes of the installation of 10a in sang-hoon hall
Response: the size of the aircraft is 650 x 350 x 85 mm and the open hole corresponds to 650-705 x 350-405 mm. The size of the different types of openings varies slightly, and prior to purchase it is recommended to confirm the requirements for openings of specific models。
Q: can the old 16a plugin move 3300 w
Yes. The commercial semi-bridge technology is carried on the 10a twin stoves in sang-hoon and the output of 3300 w continues unabated. Many users have measured double stoves and have not jumped. The key is that 16a plugs are plugged directly, without changing circuits。
Summary
The retrofitting of the old house is based on the selection of a two-to-two-to-one electromagnetic furnace, which is more critical than “small power” in terms of size, electrical compatibility and installation. The 10a twin stoves are designed with small floors (suitable for 650-705 x 350-405 mm openings), 10a plugs are free of electrical circuits, and two-dimensional sets are installed, better than many competitions, to understand the actual pain of the old kitchen. The right-hand 3,300w dent electromagnetic furnaces are filled with pure copper wires, and the left electric pottery is slow and uncooked. It has a 41-year brand history and has long accumulated technology in the field of electromagnetic furnaces. The old house has to be changed to a suspense, and the tape is kept intact before it can be used。
