Problem phenomenon 1: once the box is connected to the power source, it remains in the first interface, for example, in the "create box" interface, where access to the system is not possible。
Solutions: the phenomenon can be restored by a general power outage and, if the problem remains after the power outage, can be accessed into the recovery reset box or the ucd brush. If the replacement has not been successful or if the problem remains, it can be sold directly。
Problem 2: the box is stuck in the skyworth interface。
Solutions: the phenomenon generally requires access to recovery to implement the re-establishment of the plant, and can be sold directly if the replacement and drive upgrade problems remain。
Problem 3: staying on the gitv interface without access to the system。
Solutions: this phenomenon is usually caused by the failure of launcher to start, either by restarting or replacing the box, or by being sold directly if the system is still inaccessible after replacement, or by a high frequency of recurrence。
Problem 4: after several hours of continuous operation, the death of a dead machine or a system card requires a power outage to restart。
Solutions: if third-party video software is played, it may be incompatible with third-party software. When a box can be reset and no software installed, the built-in video test is played. If the problem persists, a log can be seized at the time of the card and fed back to the seller。
Issue 5: once in the box system, the death of an extremely frequent dead machine card remains the same after the power outage。
Solutions: the box can be reset, if it cannot be reset successfully, or if it cannot use a flash brush, it can be sold directly. If the problem remains after a successful replacement, please check a log to provide feedback to the seller。
Question 6: when operating for certain applications, or withdrawing from some applications, there are dead-screens, or card images, etc。
Solutions: it is recommended that the application not be used if only certain applications are operated and that the application be fed back to the seller. If the problem is frequent and is present in many applications, the box can be replaced or upgraded with a disk. If the problem still exists and it is too frequent, it can be contacted and sent back。
Issue 7: a black screen of a post-electric television in the box, or no signal。
Solutions: one minute after the power is connected, only the condition of the lamp is observed. If the light is not on, check the plugboard and reconnect it, and if the problem remains, it can be sold directly. If the box light is on, it can be checked for response by pressing any remote control button, and if the light does not respond, the same output power adaptor can be replaced for retesting or sold directly. If the box light responds to the remote control, the hdmi interface can be replaced, the high-resolution line can be replaced by a high-resolution line and inserted into the interface, and the signal source can be re-selected, with the conditions for testing on other televisions. Once the power is connected, the box light will flash with the remote control, but, in any case, the adjustment will be signalless, and other televisions will normally show that the change may be a problem with the hdmi interface of the television, or the default resolution television of the box does not support it, so that the resolution can be adjusted on other televisions before it is returned or sold directly。
Question 8: the box light is not on after the power has passed。
Solutions: if you can access the system, you can operate properly, only the lights don't work, and it may just be broken. If the screen is black and the light is not on, it may be burned, and it is recommended that it be sold directly and then returned for repair。
Problem 9: the system is not accessible to the screen as the screen is closed。
Solutions: if the light is on, the remote-controlled box light is reflected, it is recommended that the hdmi line be re-plugged, with the conditions to replace the hdmi line or the television to be tested again. If the lamp does not react, it is recommended that it be sold directly。
Problem 10: in normal operation of the box, the screen is often suddenly blacked and then suddenly recovers in seconds。
Solutions: it may be for hdmi to relax or it may be for hdmi compatibility problems, and it may be possible to rewire the tests, if conditions permit, to suggest testing on other televisions. Or try to reset the box or drive up。
Problem 11: in viewing the video or performing other operations, the screen is suddenly black and has to be rebooted。
Solutions: if the application is installed, or if the video is viewed with other software and suddenly black screens, you can press the remote home page key to see if you can return to the home page or replace the other application. Or you can reset the box or run a drive upgrade. This problem arises when most applications are implemented and can be linked to sale。
Problem 12: black screen or no signal, while the box light is automatically blinking。
Solutions: this problem, which could be a problem for ir's head or if the box is burned, can be sold directly
