Product strengths and characteristics:
Clean environment
The entire system operates under full negative pressure, is secure, is free of dust spills, is environmentally clean, and the finished products are collected using a bag cleaner, with as much as 99. 9 per cent dust removal efficiency above the state-of-the-art environmental standards; the hlm mill's limit is designed to ensure that the grinding disks and grindings do not touch during work, with small vibrations and low noise。
2. High yield efficiency
The grinding is efficient and energy-depleted, saves 30-50 per cent of electricity consumption compared to the ball grinding machine, the plate structure is well designed, the grinding curve is long and the grinding area is large; the limit is designed to prevent grinding, direct contact with the grinding plate, and the grinding of the grinding lid and the lining is less damaged; the grinding tatter can be turned over and its useful life doubled; and the hydraulic loading system is equipped with a flexible adjustment of the pressure to allow for permanency changes and high energy efficiency。
3. High level of automation
The hlm stand-by mill uses a fully automated control system, which allows for remote manipulation and ease of operation; the limit device prevents direct contact with the grinder, which can be launched emptyly without pre-opening fabric; the external independent rare oil lubricating station, which facilitates the replacement of oil, the speed-reducing machine and the grinding bearings, which use compulsory rare oil lubrication, which takes a large amount of heat at the same time, and increases the useful life of the speed-reducing and grinding axes; and the hydraulic control device can easily drive out the grinding machine, sharpening gear replacement and polishing。
4. Quality stability and reliability
Use of dynamic, environmentally friendly pollinators, concentration of particle distribution, good particle shape, variable-frequency modulation, ease of product fine-tuning; milling accompanied by timely selection of finished products to reduce the length and frequency of stopovers and cycles in the material mills, and small and high quality contamination of the finished products。
5. Low cost of integrated investments
Owing to the fact that the process is simple, compact, small, open-air and lower construction costs, as a result of milling, grading, drying and delivery, the process is simple, the layout is compact, the area is small, the construction costs can be reduced; there is a drying function, which provides thermal ventilation, sufficient exposure to powder materials in the grinding, multiple times, and a drying unit is saved. By regulating the temperature of the hot wind, the drying requirements of the different wet material can be met, with a maximum of 15 per cent drying of the material。
Ii. Hlm logic
The hlm series of stand-by grinder main generators rotate the grinder through the decelerator and the fixed grinder rotates around the roller. The material falls from the bottom to the centre of the grinding board, which is operated by a centrifugal force, moving at a flat pace from the centre of the grinding board to the edge, through a grinding roller, under grinding pressure, which is provided by a hydraulic loading system, large pieces of material are crushed directly, and fine particles are squeezed and crushed to form a particle bed for inter-pumping。
Drying and milling are carried out simultaneously, with a hot wind smoothing around the grinding board through the wind ring, drying out the shredding material cut from the grinding board and delivered to the upper pollen, with rough particles back to grinding (inner cycle) on the grinding board by rotor blades, with qualified fine powder grinding together and collected by the system aggregater as a finished product, and with small amounts of larger particles, impurities, etc., that are difficult to crush and cannot be blown by a single wind, falling through the grinding ring to the scraping unit in the lower part of the mill, or with delivery equipment coming into grinding (out of the outer cycle) through the intake。
Iii. Hlm coal powdering parameter
Coal mill production: 6-80t/h
Coal powder detail: r0. 08 = 5-15%
Coal powder moisture: ≤1-5%
Iv. Product delivery site
V. Prices and after-sale services
The hlm series of stand-alone mills are new grinding equipment developed by the red star group to meet the needs of its customers, in combination with market demand. Their out-of-fact prices are absolute and high. The red star machine has been developing for more than 40 years, and its quality and reputation are limited in industry。
"creating red stars, satisfiing clients" is the eternal pursuit of the red star group. The red star group has a well-established system of after-sales services, eagerly and in the best of its ability to save time and bring more economic value to its clients。
Maximum breakthrough, innovation. From high-yield energy efficiency to clean environment, from mill efficiency to automation, the red star hlm set of milling equipment has been technically empowering to build new poles for millers in the industry from a user perspective and to create a new future for milling with clients。
