In the diy installed market, separate water cooling programmes are often more time-consuming, labour-intensive and expensive, while integrated water coolers are mostly designed for cpus. Today, when gpus are much more exhausted than cpus, it becomes difficult for players to find an ideal graphic-water cold-dispersion program. Today, we bring you a one-size-fits-all card cooler, id-coling icekimo 240vga, which will help you solve the problem of card spread。
Look first at the main part of the id-coling icekimo 240vga water cooler, whose front is designed in a very graphic style, where the shell of the black sanded metal with the green metal plate appears to be of good quality and can also be a good protection for the pcb plate, and where the 9cm special fans on the right of the logo can also provide some sort of dispersive help to the graphic card power section。
The luminous logo at the top is id-cooling, which can send a green light after the power goes off。
On the back, a large area of water cold can be seen, which is officially claimed to support graphic cards 58. 4 x 58. 4 mm, 53. 3 x 53. 3 mm, 51 x 61 mm, and is basically supported by medium-high-end graphic cards of both nvidia and amd, although we note that, in order to satisfy the heat of the electricity supply, it is more recommended that the radiator be applied to standard heights and that the power supply component be designed for long cards on the right. It is worth mentioning that, in order to facilitate line management, the plant brought together all the electricity from the electric fans, the water cooling head, and the green logo light at the top into a small pcb board to provide electricity through an external 3-pin line。
After talking about the bulk of the radiator, let's look at the chiller section, where id-coling icekimo 240vga uses a 240-wind water cooler, which sizes 275 x 120 x 27 mm, although it is a 240-size chiller, but which is close to 280 mm in length, so the players must be careful whether or not they can accommodate the case. The water cooling tube is rubber-based and is externally packaged with nylon wire to increase the intensity to prevent aging of the rubber, with a pipe length of 315 mm and a pipe diameter of 12 mm. Two sf-series green light fans with a diameter of 12 cm use hb hydraulic bearings, 4pin designed for controlled retro-velocity, with a speed range of 800-2000 rpm。
Two sf-series green light fans with a diameter of 12 cm use hb hydraulic bearings and 4pin is designed for controlled speed rotation。
A 240-wind water cooler with a moderate distribution of dispersed fins with a size of 275 x 120 x 27 mm was used。
The spare parts are also very rich, with a total of 12 visible bulk thermometers, 8 cold rows of fixed long screws, 8 fan-fixed short screws, a four-pin one-half line, a small syringe silicon, nine insulation gaskets, a barrel of dispersed hot glue, four cold-head fixed screws and a metal cold-head fixed rack。
After presenting the dispersive structure of id-coling icekimo 240vga, it is believed that what you expect most is its actual dissipation effect. To experience its dispersive effects, the installation of water coolers is a natural necessity. We take the public version of gtx 1080, for example, first of all by dismantling the original bulk heater and separating the pcb board from it. It then adjusts the position of the screws on the water cooling head to the point on the pcb plate, after which it binds the metallic dispersors to the visible particles and to the power supply module through the conductive thermal glue to assist the dispersion。
The back of the radiator appears to be empty because of the need to install more compatible graphic cards。
It will then be possible to install water coolers, which will require careful use of red pads in the fittings, avoid damage to the pcb plate, tie them together and fix the metal slabs on the back and tighten the screws to complete the installation, which will be easier to install, even without reading the instructions, which will be very humane for some players who are less able to do it。
Following the installation of the radiator, we were able to test thermal expression in the stand-by state and under the fui mark oven, and on board, care was needed to fit as much as possible the 4pin temperature line of the cold-team fan on the main plate cpu chafan interface to ensure optimal dissipation and silent effects. As can be seen from the test results, the performance of the d-coling icekimo 240 vga water cooler and the original titanic heater are not very different in the stand-by state, and they are generally at about 32°c. However, after 10 minutes of operation of the furmark oven software, the maximum core temperature of gtx 1080 after icekimo 240vga water cooler is only 60°c, which is much better than the original 85. 0°c core temperature of the titanic radiator, and the difference between the two is significant, and in the course of the testing we have also noted that icekimo 240vga water cooler is used at a slower and less noise rate and provides a good game environment for players。
The overall performance of id-coling icekimo 240vga as a single water cooler is satisfactory. The black, green-coloured metal casings with green led lamps are in no way different from some non-public cards, but the back of the radiator appears to be empty because of the need to install more compatible graphic cards. Icekimo 240vga can be easily suppressed, even with high performance graphic cards such as gtx 1080, and has a clear advantage over the original wind heater. As far as prices are concerned, the price of $499 is modest, and if you're worried about the choice of an ideal one-size-fits-all water cooling card radiator, then id-coling icekimo 240vga is a good option。
Basic parameters
Applicable products: mainstream card holes on the market (pore 58. 4 x 58. 4 mm, 53. 3 x 53. 3 mm, 51 x 61 mm)
Diffusion method: water cooling and spreading
Fan rotation: 800~2000rpm
Fan size: 120 mm x 120 mm x 25 mm
Maximum wind: 84. 5 cfm
Cold platoon size: 275 mm x 120 mm x 27 mm
Power interface: 4pinx2,3pinx1
Reference price: $499
Advantages: simple installation, dissipation better
Disadvantages: thinner back of the radiator
